ACV 42k-1250-000 - LFB for Nissan/Renault/Dacia/Opel to ISO/Mini

Steering wheel remote control adapter Dacia / Nissan / Opel / Renault

Keep the original steering wheel remote control functions if you replace your factory radio with an aftermarket radio.
Please compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.

Suitable for the following vehicles:

Dacia

• Dacia Duster (SD) 04/2010 - 11/2013*
• Dacia Sandero (SD) 06/2008 - 12/2012*

Nissan

• Nissan NV400 (X62) 09/2010 - 06/2014
• Nissan NV400 (X62) 07/2014- 07/2020**
• Nissan Primastar (X83) 11/2002 - 09/2006
• Nissan Primastar (X83) 09/2006 - 05/2015**

Opel

• Opel Movano B (X62) 05/2011 - 05/2019**
• Opel Vivaro A (X83) 01/2001 - 09/2005
• Opel Vivaro A (X83) 09/2006 - 12/2010
• Opel Vivaro A (X83) 09/2011 - 07/2014**

Renault

• Renault Clio II (B) 09/1998 - 03/2002
• Renault Clio II (B) 07/2001 - 09/2005
• Renault C lio II (B) Campus 09/2005 - 04/2009
• Renault Kangoo I (KC) 01/1998 - 04/2003
• Renault Kangoo I (KC) 04/2003 - 12/2009
• Renault Master II 03/1998 - 09/2002
• Renault Master II (JD) 02/2002 - 02/2010
• Renault Master III (M) 09/2014 - 09/2019**
• Renault Megane I (BA/DA) 03/1999 - 09/2003
enault Megane II (CM/EM) 10/2002 - 12/2005
• Renault Trafic II (J/JL) 01/2001 - 10/2006
• Renault Trafic II (I/JL) 10/2005 - 12/2010*
• Renault Trafic II (I/JL) 01/2011 - 08/2014**
• Renault Twingo I (C06) 09/1998 - 09/2003
• Renault Twingo I (C06) 01/2003 - 07/2007
• Renault Twingo II (N) 09/2007 - 12/2011**
• Renault Twingo II (N) 01/2012 - 08/2014**

The following signals are provided:

• Steering wheel remote control

*Vehicles with Blaupunkt 1-DIN OEM device
**Vehicles with 1-DIN OEM device AUX Front/ 1 rotary control

General installation instructions:

Check:

1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power
3: Check all interface connections for correctness and continuity without power

Connection andd connection sequence:

1: Make settings and hardware configuration of the interface without power
2: Check configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with the live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

1: Make changes without power supply
2: Connection after change see above 5 to 8

If the interface or the Vehicle:

1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Anschluss nach CAN Bus rest see above 5 to 8
Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended exclusively for orientation and information for trained specialists.

Further connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

1: Connections and modifications may only be carried out by trained specialists
2: Connections and modifications must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and modifications must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and modifications are made at your own risk and there is no guarantee of functionality
5: Connections and modifications are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
6: Modifications to the pre-assembled wiring harness can void the product's warranty