ACV 42xfo003-0 - LFB Ford vehicles, 40Pin Quadlock, Multilead CAN Bus loose

Steering wheel remote control adapter Ford

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle equipment and the range of functions and software of the aftermarket device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Suitable for the following vehicles:

• Ford C-Max (DM2) 11/2003 - 05/2007
• Ford C-Max (DM2) 05/2007 - 09/2010
• Ford Fiesta (JH1/JD3) 10/2005 - 09/2008
• Ford Focus (DA3) 11/2004 - 03/2008
• Ford Focus (DA3) 02/2008 - 03/2011
• Ford Fusion (JU2) 10/2005 - 07/2012
• Ford Galaxy II (WA6) 03/2006 - 04/2010
• Ford Galaxy II (WA6)05/2010 - 
• Ford Fusion (JU2) 10/2005 - 07/2012
• Ford Galaxy II (WA6) 03/2006 - 04/2010
• Ford Galaxy II (WA6)05/2010 - 05/2015
• Ford Kuga (DM2) 06/2008 - 12/2012
• Ford Mondeo III (B4Y/B5Y/BWY) 06/2003 - 04/2005*
• Ford Mondeo III (B4Y/B5Y/BWY)05/2005 - 06/2007*
• Ford Mondeo IV (BA7) 06/2007 - 10/2010*
• Ford Mondeo IV (BA7) 11/2010 - 08/2014*
• Ford S-Max (WA6) 06/2006 - 04/2010
• Ford S-Max (WA6) 05/2010 - 05/2015
• Ford Transit (F**6) 07/2006 - 03/2014
• Ford Transit Connect (P*2) 06/2006 - 07/2013

The following signals are provided:

• Reimported vehicles or vehicles with different software may be incompatible in terms of functions be.
• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V reversing signal
• pink: speed signal
• green: ground GND handbrake signal
• Output load capacity: 250 mA max.

Current requirement greater than 250 mA:

• 1 relay coil resistance 75 Ohm min.
• 2 relays Coil resistance 150 Ohm min.
• Steering wheel remote control

*Vehicles with PDC > Function test without OEM device
*Vehicles with PDC without function > Article: 42sfo011

General installation instructions:
Check:

• 1: Check all operating functions and vehicle setting functions of the OEM device
• 2: Dismantle the OEM device without voltage
• 3: Check all interface connections for correctness and continuity without voltage

Connection and connection sequence:

• 1: Settings and carry out the hardware configuration of the interface without voltage
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions for the retrofit device
• 4: Connect all other connections according to the operating instructions for the retrofit device
• 5: Connect the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and more
• 8: Functional test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

• 1: Make changes without power supply
• 2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:

• 1: Revert to the OEM device
• 2: Operate the OEM device
• 3: Establish CAN bus rest
• 4: Check the hardware configuration of the Interfaces
• 5: Connection after CAN bus rest, see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Other connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

• 1: Connections and changes may only be carried out by trained specialist personnel
• 2: Connections and changes must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes
• 3: Connections and changes must be checked before connection by measuring and by to check the alignment for functionality and correctness using the vehicle's cable assignment plan
• 4: Connections and changes are made at your own risk with no guarantee of functionality
• 5: Connections and changes are made at your own risk with no guarantee of damage to the vehicle, the retrofit device or the interface
• 6: Changes to the pre-assembled wiring harness can void the product's warranty