ACV LFB Suzuki various vehicles 20Pin Honda analog

Product information ACV LFB Suzuki various vehicles 20-pin Honda analog

Keep the original steering wheel remote control functions when replacing the factory radio with a retrofit radio.
Depending on the vehicle equipment and the range of functions and software of the  retrofit device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

For the following vehicles suitable:

• Suzuki Baleno (EW) 06/2016 - 07/2019
• Suzuki Ignis (MF) 01/2017 - 04/2020
• Suzuki Ignis (MF ) 04/2020 - 2024
  Suzuki Jimny (GJ) 10/2018 - 09/2020
  
• Suzuki Jimny (GJ) 10/2018 - 09/2020
• Suzuki Jimny NFZ (GJ) 04/2021 - 2024
  
• Suzuki Kizashi (FR) 10/2010 - 08/2015
• Suzuki Swift (FZ/NZ) 09/2010 - 10/2013
• Suzuki Swift (FZ/NZ) 10/2013 - 04/2017
  
• Suzuki Swift (AZ) 04/2017 - 07/2020
• Suzuki Swift (AZ) 07/2020 - 03/2024
• Suzuki Swift Sport (AZ) 04/2020 - 2024
• Suzuki SX4 S-Cross (JY) 10/2013 - 07/2017
• Suzuki SX4 S-Cross (JY) 10/2016 - 12/2021
  
• Suzuki Vitara (LY) 04/2015 - 08/2018
• Suzuki Vitara (LY) 10/2018 - 2024

The following signals are provided:

• Reimported vehicles or vehicles with different software may be incompatible in terms of functions.
• Steering wheel remote control

Connection cable for the following radio manufacturers:

• LFB InCartec cable > Blaupunkt/China HU/Kenwood: 42k-000
• LFB InCartec cable > Multilead various devices: 42k-025
• LFB InCartec cable > Alpine: 42k-100
• LFB InCartec cable > Blaupunkt/Kenwood/Pioneer: 42k-300
• LFB InCartec cable > XZent/ Zenec: 42k-400
• Sony: 42k-600
• LFB InCartec cable > Kenwood: 42k-700a
• LFB InCartec cable > Clarion: 42k-800
• LFB InCartec Cable > JVC: 42k-900

General installation instructions:

Check:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without voltage
3: Check all interface connections for correctness and continuity without voltage

Connection and Connection sequence:
1: Make the settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with the live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without power supply
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Anschluss nach CAN Bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions Cables are intended solely for orientation and information purposes for trained specialist personnel.

Other connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and changes are made at your own risk and there is no guarantee of functionality
5: Connections and changes are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness may void the product's warranty lead