ACV 2-Din radio panel for Seat/VW with LFB

Product information ACV 2-Din radio panel for Seat/VW with LFB

Many car manufacturers install their own vehicle-specific radios that are visually adapted to the center console.
Installation kits contain all components for replacing an OEM device.
Depending on the vehicle's equipment, all adapters and interfaces required to operate the retrofit device and to restore vehicle functions are included in the scope of delivery.
Please note the installation recommendations for the individual components.
In some cases, not all vehicle functions are supported.
For example, Trailer Assist, E Call or other driver assistance systems.
Before installation, check the OEM device and the vehicle menu for various settings.
Depending on the vehicle equipment and the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Suitable for the following vehicles:

Seat

• Seat Alhambra II (7N) 06/2016 - 08/2019

VW

• VW Amarok (2H) 09/2016 - 07/2020*
• VW Beetle (16) 06/2016 - 03/2018
• VW Caddy IV (DU) 06/2015 - 09/2020
• VW Sharan II (7N) 07/2015 - 10/2021
• VW T6 (7HC) 07/2015 - 0 8/2019**

Colour: 

• black

Installation cutout for radio display: 

• 173 mm x 98.5 mm

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

• pink: +12V ignition terminal 15 1.5A max.
• orange: +12V lighting terminal 58 0.1A max.
• white: +12V reversing signal 1.5A max.
• yellow/green yellow/red: speed signal

Steering wheel remote control

• *Vehicles with OEM device including CD Drive
• **Vehicles without Composition Audio MIB Entry OEM device with front AUX/SD/USB
• **Vehicles with Composition Audio MIB Entry OEM device with front AUX/SD/USB > Article: 42a-1324-001

Scope of delivery:

• 2-DIN radio panel Seat/Skoda/VW various vehicles black > Article: 381320-30-1
• LFB Audi/MAN/Seat/Skoda/VW various vehicles 52Pin Quadlock > Article: 42a-1328-000
• LFB cable 42a/42cx401 > Multilead various devices > Article: 42arc100
• Antenna adapter Fakra(m)(Set)>DIN(m) 12V Phantom loose > Article: 1524-70-0

General installation instructions:

Check:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power supply
3: Check all interface connections for correctness and continuity without power supply

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with a live connection last
6: Configure the software of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without voltage
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Further connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked before connection for any manufacturer approvals or for any manufacturer warranty conditions that may be affected by the changes
3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and changes are made at your own risk and there is no guarantee of functionality
5: Connections and changes are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness can void the product's warranty