ACV 611094-35-1 - 2-DIN kit with compartment for Citroen/Fiat/Opel/Peugeot with LFB

Radio panel 2-DIN with compartment with radio connection kit steering wheel remote control Citroen / Fiat / Opel / Peugeot

Many car manufacturers install their own vehicle-specific radios that are visually adapted to the center console.
Installation kits contain all components for replacing an OEM device.
Depending on the vehicle's equipment, all adapters and interfaces required to operate the retrofit device and to restore vehicle functions are included in the scope of delivery.
Note the installation recommendations for the individual components.
In some cases, not all vehicle functions are supported.
For example, Trailer Assist, E Call or other driver assistance systems.
Before installation, check the OEM device and the vehicle menu for various settings.
Depending on the vehicle equipment and the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.
/>Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Suitable for the following vehicles:
Citroen

• Citroen Jumper (250) 05/2014 - 10/2022
  
• Citroen Jumper (250) 10/2022 - 2024
  
• Citroen e-Jumper (259 10/2021 - 2024
• Citroen Relay (250) 2006- 2024

Fiat

• Fiat Ducato (ZAF 250) 05/2014 -11/2021

Opel

• Opel Movano Cargo C (Y) 10/2021 - 01/2024
• Opel Movano Cargo C (Y) 01/2024 - 2024
• Opel Movano Electrik Cargo C (Y) 10/2021 - 01/2024
• Opel Movano Electrik Cargo C (Y)  01/2024 - 2024

Peugeot

• Peugeot Boxer (Y) 09/2014 - 12/2019
  
• Peugeot Boxer (Y) 08/2018 - 2024
  
• Peugeot e-Boxer (Y) 10/2021 - 2024

Color:

•  Piano lacquer black

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V Reverse signal
• pink: speed signal
• green: ground GND handbrake signal
• Load capacity of total outputs: 100 mA max.
• Current requirement greater than 100 mA:
• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.
• Steering wheel remote control

*Vehicles with Daiichi OEM Device wiring harness black cable > adapter wiring harness radio slot driver's side dismantle
*Vehicles with directly wired OEM Daiichi device colored cable not compatible > contact support
**On-board computer vehicle settings:
2-DIN kit Citroen/Fiat/Opel/Peugeot with OEM device info adapter > article: 62-1094-35-2

Scope of delivery:

• 2-DIN radio panel with compartment Citroen/Fiat/Opel/Peugeot > article: 281094-35-1
• LFB Citroen/Fiat/Opel/Peugeot VP1/VP2/Daiichi 52Pin > Article: 42sfa019
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022> > Article: 42ctmultilead3
• Antenna adapter Fakra(m)>DIN(m) passive > Article: 1524-01

General installation instructions:
Check:

1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power supply
3: Check all interface connections for correctness and continuity without power supply

Connection and connection sequence:

1: Make the settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with a live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Functional test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

1: Make changes without voltage
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:

1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus peace
4: Checking the hardware configuration of the interface
5: Connection to CAN Bus rest see above 5 to 8

Further connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and changes must be checked for function and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and changes are made at your own responsibility and there is no guarantee of functionality
5: Connections and changes are made at your own risk and there is no guarantee against damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness can void the product's warranty