ACV 621023-18-2 - 2-DIN kit for BMW 3 Series (E46), 07/1998-02/2007, LFB/antenna

Radio panel 2-DIN with radio connection kit steering wheel remote control / BMW

Many car manufacturers install their own vehicle-specific radios that are visually adapted to the center console.
Installation kits contain all components for replacing an OEM device.
Depending on the vehicle's equipment, all adapters and interfaces required to operate the retrofit device and to restore vehicle functions are included in the scope of delivery.
Note the installation recommendations for the individual components.
In some cases, not all vehicle functions are supported.
For example, Trailer Assist, E Call or other driver assistance systems.
Before installation, check the OEM device and the vehicle menu for various settings.
Depending on the vehicle equipment and the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions.
Compare the shown plug of the adapter with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Color:

•  black

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

• Steering wheel remote control

17 pin BMW connector:

*Cable extension BMW 17 pin(f)>17 pin(m)/antenna 6.5m loose > Article: 1020-21-6500-0
**Vehicles with sound system (not DSP/Harman Kardon) Active system adapter BMW/Land Rover/Rover 17 pin > Article: 13-1020-50

40 pin BMW connector:

*Cable extension BMW Quadlock(m/f)/antenna 6.5m loose > 1024-25-6500-0
**Vehicles with sound system (not DSP/Harman Kardon) LFB BMW 3 Series/5 Series/7 Series/X3/X5/Z4/  Mini Quadlock/Amp > Article: 42sbm007

Scope of delivery:

• 2-DIN radio panel BMW 3 Series (E46) central installation > Article: 381023-16
• LFB BMW/Mini various vehicles 17Pin/Quadlock IBus > Article: 42sbm00c
• Antenna adapter Fakra(m)>DIN(m) passive: Article: 1524-01
• Antenna adapter ISO(f)>DIN(m): 1500-00
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>> > Article:  42ctmultilead3

General installation instructions:
Check:

1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power supply
3: Check all interface connections for correctness and continuity without power supply

Connection and connection sequence:

1: Make the settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with a live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

1: Make changes without power supply
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:

1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Checking the hardware configuration of the interface
Anschluss nach CAN Bus-Ruhe see above 5 to 8

Further connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan to be checked
4: Connections and changes are made at your own risk and there is no guarantee of functionality
5: Connections and changes are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness can void the product's warranty