ACV 42xbm00c - LFB BMW/Mini vehicles 17Pin/Quadlock IBus Multilead

Steering wheel remote control adapter BMW / Mini

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle equipment and the range of functions and software of the aftermarket device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Suitable for the following vehicles:
BMW:

• BMW 3 Series (E46) 07/1998 - 02/2007
• BMW 5 Series (E39) 01/1996 - 05/2004
• BMW 7 Series (E38) 09/1994 - 09/2001
• BMW X3 (E83) 02/2004 - 08/2010
• BMW X5 (E53) 03/2000 - 11/2006
• BMW Z4 (E85) 03/2002 - 08/2008***

Mini:

• Mini (R50/R53) 06/2001 - 11/2006
• Mini (R52) 07/2004 - 08/2008

The following signals are provided:

• Reimported vehicles or vehicles with different software may be incompatible in terms of functions. be.
• Steering wheel remote control

17 pin BMW connector:

• *Vehicles with Professional Navigation BMW extension 17 pin(f) > 17 pin(m)/antenna 6.5m > Article: 1020-21-6500-0
• **Vehicles with sound system (not DSP/Harman Kardon) active system adapter BMW/Land Rover/Rover 17 pin > Article: 13-1020-50

40 pin BMW connector:

• *Vehicles with Professional Navigation BMW extension Quadlock(f) > Quadlock(m)/antenna 6.5m > Article: 1024-25-6500-0
• **Vehicles with sound system (not DSP/Harman Kardon) LFB BMW 3 Series/5 Series/7 Series/X3/X5/Z4/ Mini Quadlock/Amp > Article: 42xbm007
• ***Vehicles with fabric roof 

General installation instructions:
Check:

• 1: Check all operating functions and vehicle setting functions of the OEM device
• 2: Dismantle the OEM device without applying any tension
• 3: Check all interface connections for correctness and continuity without applying voltage

Connection and connection sequence:

• 1: Make the settings and hardware configuration of the interface without applying voltage
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions for the retrofit device make
• 4: Make all other connections according to the operating instructions for the retrofit device
• 5: Connect the entire installation to the vehicle with the live connection last
• 6: Configure the software of the interface according to the instructions in the article text and in the BDA
• 7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and further
• 8: Function test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

• 1: Make changes without power supply
• 2: Connection after change see above 5 to 8

If the Interface or the vehicle:

• 1: Revert to the OEM device
• 2: Operate the OEM device
• 3: Establish CAN bus rest
• 4: Check the hardware configuration of the interface
• 5: Connection after CAN bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Other connections, changes to the cable configuration of the cable harness or use of alternative connections or connection extensions:

• 1: Connections and changes may only be carried out by trained specialist personnel
• 2: Connections and changes must be checked for any defects before connection. Manufacturer approvals or manufacturer warranty conditions that may be affected by the changes must be checked
• 3: Connections and changes must be checked for functionality and correctness by measuring and comparing against the vehicle's cable assignment plan before connection
• 4: Connections and changes are made at your own risk with no guarantee of functionality
• 5: Connections and changes are made at your own risk with no guarantee of damage to the vehicle, the retrofit device or the interface
• 6: Changes to the pre-assembled wiring harness can void the warranty of the product