ACV LFB Ford Fiesta/Transit/Transit Custom 32Pin Ford

ACV LFB Ford Fiesta/Transit/Transit Custom 32Pin Ford

Steering wheel remote control adapter Ford

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.

Depending on the vehicle equipment and the range of functions and software of the  retrofit device, individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before final assembly, check vehicle functions, Check vehicle settings and steering wheel remote control for functionality.

Note:

CAN Bus

Connection: 32 pin Ford connector

Vehicles with OEM rear view camera:
Rear view camera adapter OEM camera 52 pin Fiat/32 pin Ford > Article: 771000-2000

yellow: video+
black: video

Check the assignment for correctness by measuring before installation
Pin 14: video+
Pin 25: video-

Troubleshooting for flickering camera image: Connect video pin 25 to pin 24

Suitable for the following vehicles:

• Ford Fiesta (JHH) 06/2017 - 03/2022
• Ford Fiesta (JHH) 03/2022 - 2024
• Ford Transit (FAC/FAD) 06/2019 - 2024
• Ford Transit Custom (FAC/FAD) 01/2018 - 2024

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

red: +12V ignition terminal 15
orange: +12V lighting terminal 58
purple/white: +12V reverse gear signal
pink: speed signal
green: ground GND handbrake signal

Total output load capacity: 100 mA max.

Current requirement greater than 100 mA:
1 relay coil resistance 75 Ohm min.
2 relay coil resistance 150 Ohm min.

Steering wheel remote control

Connection cable for the following radio manufacturers:

• LFB cable 42s/acv > Alpine jack: 42ctalpinelead
• LFB cable 42s/acv > Parrot 4 pin: 42ctasteroidlead
• LFB cable 42s/acv > Bosch-Blaupunkt >2010 Mini ISO: 42ctblaupunktlead
• LFB cable 42s/acv > Blaupunkt/China HU/Kenwood 3 cable: 42ctchinahulead
• LFB cable 42s/acv > Clarion jack: 42ctclarionlead
• LFB cable 42s/acv > Garmin Vieo" RV52 Stereo Dock 3 cable: 42ctgarminlead
• LFB cable 42s/acv > JVC 1 cable/jack: 42ctjvclead
• LFB cable 42s/acv > Kenwood 1 cable: 42ctkenwoodlead
• LFB cable 42s/acv > Multilead various devices: 42ctmultilead
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead3
• LFB cable 42s/acv > Multilead various devices/Pioneer 2022>: 42ctmultilead5
• LFB cable 42s/acv > Panasonic 1 cable: 42ctpanasoniclead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Pioneer jack: 42ctpioneerlead
• LFB cable 42s/acv > Pioneer AVH/DMH/SPH 2022> jack loose: 42ctpioneerlead2
• LFB cable 42s/acv > devices with LFB learning function: 42ctsmartlead
• LFB cable 42s/acv > Blaupunkt/Kenwood/Sony jack: 42ctsonylead
• LFB cable 42s/acv > XZent/Zenec 1 cable: 42ctzeneclead

General Installation instructions:

Check:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without voltage
3: Check all interface connections for correctness and continuity without voltage

Connection and connection sequence:
1: Make the settings and hardware configuration of the interface without voltage
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with a live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configure the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and further
8: Function test of steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without voltage
2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest see above 5 to 8

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Other connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes may only be made by trained qualified personnel
2: Connections and changes must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and changes must be checked for functionality and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and changes are made at your own risk and there is no guarantee of functionality
5: Connections and changes are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
6: Changes to the pre-assembled wiring harness can void the product's warranty