ACV 42xns009-0 - LFB Nissan Pulsar/Qashqai/X-Trail, 20Pin/32Pin Multilead

Steering wheel remote control adapter Nissan

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.
Depending on the vehicle equipment and the range of functions and software of the  aftermarket device, individual operating functions may be omitted or replaced by other functions.
Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.
Please also check whether one of the specified original factory radios was installed in your vehicle.
Before final assembly, check the vehicle functions, vehicle settings and steering wheel remote control for functionality.

For the following vehicles suitable:

• Nissan Pulsar (C13) 10/2014 - 06/2018
• Nissan Qashqai (J11) 03/2014 - 07/2017*
• Nissan X-Trail (T32) 07/2014 - 07/2017*

The following signals are available provided:

• Reimported vehicles or vehicles with different software may be incompatible in terms of functions.
• red: +12V ignition terminal 15
• orange: +12V lighting terminal 58
• purple/white: +12V reversing signal
• pink: speed signal
• green: ground GND Handbrake signal
• Output load capacity: 250 mA max.

Current requirement greater than 250 mA:

• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.
• Steering wheel remote control
• Date/time settings supported

*Vehicles with 360° OEM camera system Item in preparation:
LFB Nissan Qashqai/Rogue/X-Trail 20Pin/32Pin camera > Article: 42xns025

General installation instructions:
Check:

• 1: Check all operating functions and vehicle setting functions of the OEM device
• 2: Dismantle the OEM device without voltage
• 3: Check all interface connections for correctness and continuity without voltage

Connection and connection sequence:

• 1: Make the settings and hardware configuration of the interface without voltage
• 2: Check the configuration of the radio connection cable
• 3: Connect the radio connection cable according to the operating instructions for the retrofit device
• 4: Connect all other Make connections according to the operating instructions for the retrofit device
• 5: Connect the entire installation to the vehicle with the live connection last
• 6: Software configuration of the interface according to the instructions in the article text and in the BDA
• 7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
• 8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:

• 1: Make changes without power supply
• 2: Connection after change see above 5 to 8

If the interface or the vehicle malfunctions:

• 1: Revert to the OEM device
• 2: OEM device operate
• 3: Establish CAN bus rest
• 4: Check the hardware configuration of the interface
• 5: Connection after CAN bus rest, see 5 to 8 above

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are intended solely for orientation and information for trained specialist personnel.

Other connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:

• 1: Connections and changes may only be carried out by trained specialist personnel
• 2: Connections and changes must be checked before connection for any manufacturer approvals or for any manufacturer warranty conditions that may be affected by the changes
• 3: Connections and changes must be checked for function and correctness before connection by measuring and comparing using the vehicle's cable assignment plan
• 4: Connections and changes are made at your own risk and there is no guarantee of functionality
• 5: Connections and changes are made at your own risk and there is no guarantee of damage to the vehicle, the retrofit device or the interface
• 6: Changes to the pre-assembled wiring harness can void the product's warranty