LFB Toyota vehicles 10Pin/6Pin/28Pin Multilead analog

Steering wheel remote control adapter Toyota

Keep the original steering wheel remote control functions when replacing the factory radio with an aftermarket radio.

Depending on the vehicle equipment and the range of functions and software of the aftermarket device, individual operating functions may be omitted or replaced by other functions.

Compare the adapter plugs shown with those in your vehicle and make sure that they fit visually and technically.

Please also check whether one of the specified original factory radios was installed in your vehicle.

Before final assembly, check vehicle functions, vehicle settings and steering wheel remote control for functionality.

Note:

analog

Connection: 10 pin / 6 pin / 28 pin Toyota plug
Connection: OEM steering wheel remote control > 3.5mm jack / loose cable

Vehicles with Matsushita / Fujitsu Ten OEM device
Vehicles with rear view camera*

Vehicles without 360° camera system**

Dipped switch settings for the retrofit device manufacturer (see BDA)

Suitable for the following vehicles:

• Toyota Auris (E150) 03/2010 - 01/2013
• Toyota Avensis (T27) 01/2012 - 06/2015
• Toyota Corolla (E170) 04/2014 - 12/2016
• Toyota Fortuner 2011 - 2015
• Toyota Hilux (N25) 12/2011 - 08/2016
• Toyota Hilux (AN1P) 11/2016 - 09/2020
• Toyota Innova 2011 - 2015
• Toyota Prius ZVW30/ZVW35 (XW3) 04/2012 - 02/2016
• Toyota Prius+ (XW3 / (XA3 / 6/2018
• Toyota Verso-S (XP12) 03/2011 - 07/2014
• Toyota Verso-S (XP12) 07/2014 - 12/2015
• Toyota Yaris (XP13) 11/2011 - 08/2014
• Toyota Yaris (XP13) 09/2014 - 03/2017
• Toyota Yaris (XP13) 04/2017 - 08/2020

The following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in terms of functions.

General installation instructions:

Check:
1: Check all operating functions and vehicle setting functions of the OEM device
2: Dismantle the OEM device without power supply
3: Check all interface connections for correctness and continuity without power supply

Connection and connection sequence:
1: Make settings and hardware configuration of the interface without power supply
2: Check the configuration of the radio connection cable
3: Connect the radio connection cable according to the operating instructions for the retrofit device
4: Connect all other connections according to the operating instructions for the retrofit device
5: Connect the entire installation to the vehicle with the live connection last
6: Software configuration of the interface according to the instructions in the article text and in the BDA
7: Configuration of the retrofit device according to the operating instructions for the retrofit device steering wheel remote control/camera/FSE/antenna phantom power and others
8: Function test of the steering wheel remote control and vehicle

Changes to the hardware configuration of the interface and the radio connection cable:
1: Make changes without power supply
2: Connect after change see above 5 to 8

If the interface or the vehicle malfunctions:
1: Revert to the OEM device
2: Operate the OEM device
3: Establish CAN bus rest
4: Check the hardware configuration of the interface
5: Connection after CAN bus rest, see 5 to 8 above

Connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the operating instructions are for guidance and information purposes only for trained specialist personnel.

Other connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes may only be carried out by trained specialist personnel
2: Connections and changes must be checked for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes before connection
3: Connections and changes must be checked for function and correctness before connection by measuring and comparing them with the vehicle's cable assignment plan
4: Connections and changes are made at your own risk and without guarantee of function
5: Connections and changes are made at your own risk and without guarantee of damage to the vehicle, the retrofit device or the interface
/>6: Modifications to the pre-assembled wiring harness may void the product warranty